EZ Lift Motorcycle Stands

Adjustable Front Stand (UFST02)

Steel Horse Fab front fork lift stand. Made from the same 1.25″ diameter tubing as all of our rear stands. This stand will lift a wide variety of bikes with either narrow forks (like a Ninja 250) or wide forks (like a CBR 1000RR). The sliding heads are made from 1/2″ thick steel and are adjustable from 7 3/8″ to 8 5/8″. The head guides are the same pieces as used on the URRS05 rear stands. Made from solid steel and milled into shape then welded on and finished off with a nice high gloss black powder coating. This front stand takes its styling cues from our very popular URRS05 rear stand so when the two are used together they look like a matched set.

Features

  • Made from 1.25″ mild steel tubing with .065″ side wall thickness.
  • 4 wheel design for superior stability. Each wheel is 3″ diameter.
  • Incorporates our E-Z Lift geometry.
  • Back braced for strength and sturdiness.
  • Looped handle for safety and security (you can cable lock it).
  • Steel rivets at the contact points to prevent scratching. Won’t tear off like rubber bumpers do.
  • Sliding heads are made from 1/2″ thick solid steel with rounded corners.
  • Strong high gloss black powder coat finish.
  • Stainless steel button head allen bolts used at fork contact point.
  • Stainless steel cones under allen bolts compensate for fork hole variances up to 1″ diameter.
  • 10mm aluminum spacers included which can be removed to lower stand height if needed.

Adjustable Rear Stand (URRS05)

This stand is designed for the true motorcycle enthusiast. With versatile lifting capabilities, this stand will work with bikes from your hardcore track bike to your favorite off road bike and most everything in between.

As long as your bike has a conventional two sided swing arm, (be it dirt or street) there is a good chance this rear stand will fit. For bikes without swing arm spools, just simply flip the heads over so the rubber coated pins are facing up and towards each other, adjust to the proper width and the stand is ready for non-spool use.

  • Incorporates our popular E-Z lift geometry.
  • Constructed of 1.25″ diameter steel tubing, .065 wall thickness.
  • Back braced for strength and stability.
  • 3″ diameter Quad wheels roll straight and steady.
  • Strong 1/2″ thick steel adjustable width heads.
  • Looped handle reduces trip hazards and offers a means to secure with a cable lock.
  • Geometrically designed to be strong yet lightweight, weighs just 11 pounds.
  • Designed for use with or without swing arm spools.
  • Steel rivets installed at ground contact points to prevent scratching.
  • Strong, durable powder coat finish in high gloss black.
  • Head guides are milled from solid steel

Fitment

  • Multi-fit capabilities, can be used with or without swing arm spools.
  • The head width can be adjusted from 10.5″ to 14.5″ to accommodate most all conventional swing arms.

The Bonneville

This is our new rear stand developed especially for the Triumph Bonneville. This stand will fit in between the stock exhaust pipes on all Bonneville models including the T100 up to 2016. Designed to lift from the bottom edge of the rear swing arm directly below the rear axle. Lift height is approx. 1.5 inches so lift effort is very minor. This rear stand will also work on the Thruxton and Scrambler.

Note: This stand will not work on the new Street Twin and on Bonneville 2017 or newer.

  • Main chassis made from 1.25 inch steel tubing.
  • E-Z Lift geometry to make lifting a breeze.
  • 4 wheels carry the load. Each wheel is 3 inches in diameter.
  • Swing arm rests on 3/4 inch rubber coated cold rolled steel pins.
  • Rivets on chassis bottom to prevent scratching.
  • Looped handle is made from 1 inch steel tubing.
  • Back braced for strength.
  • High gloss black powder coated finish.

Note: This stand does not require swing arm spools.

Customer Bikes on Stands